Alpha pots = Fail

Pickups, wiring schemes, switch techniques and onboard active electronics for guitars and basses
Post Reply
User avatar
mildew
Information
Posts: 40
Joined: 01 Jan 2015, 00:50
Has thanked: 1 time
Been thanked: 1 time

Post by mildew »

A month ago i put two linear Alpha pushpull pots in my prs dc22.

After a week, one pot failed - short circuit when turned up to 10.

Now the second one has failed with the same fault.

Contact cleaner failed to fix either one.

So for me, 100% fail rate within a month for Alpha pots...

User avatar
Blitz Krieg
Breadboard Brother
Information
Posts: 81
Joined: 18 Feb 2014, 10:57
Has thanked: 534 times
Been thanked: 2 times

Post by Blitz Krieg »

bourns?

User avatar
lolbou
Old Solderhand
Information
Posts: 2617
Joined: 18 Nov 2008, 21:38
Has thanked: 307 times
Been thanked: 225 times

Post by lolbou »

Overheated?
- Are you a mod or a rocker?
- Uh, no, I'm a mocker.

User avatar
Dirk_Hendrik
Old Solderhand
Information
Posts: 4189
Joined: 03 Jul 2007, 08:44
Location: Old Amsterdam
Has thanked: 232 times
Been thanked: 886 times
Contact:

Post by Dirk_Hendrik »

lolbou wrote:Overheated?
Exactly my thought earlier this morning. It's easy to blame the part but without any information it's far from sure the parts are to blame.
Sorry. Plain out of planes.

http://www.dirk-hendrik.com

User avatar
sinner
Old Solderhand
Information
Posts: 4709
Joined: 06 Nov 2008, 17:16
Location: ...no more
Has thanked: 1031 times
Been thanked: 908 times

Post by sinner »

I was going to blame overheating as well but didn't wanted to be a troll again

User avatar
rocklander
Old Solderhand
Information
Posts: 2726
Joined: 18 Apr 2008, 11:33
my favorite amplifier: my jansen bassman 50
Completed builds: rebote 2.5; supreaux; odie; heartthrob tremolo; ross phaser; dr. boogey; thor; baja black toast; slow gear attack, rebote, tri-vibe, small clone, little angel, magnus modulus, echo base, hex fuzz, big muff, 22/7.
Location: Rotorua, New Zealand
Has thanked: 1406 times
Been thanked: 231 times
Contact:

Post by rocklander »

Blitz Krieg wrote:bourns?
lolbou wrote:Overheated?
Image
world's greatest tautologist ...in the world
Ronsonic wrote:...the lower the stakes the more vicious the combat.

User avatar
Jarno
Resistor Ronker
Information
Posts: 356
Joined: 12 Nov 2008, 10:18
my favorite amplifier: Something nice
Completed builds: Alembic-like state-variable and sallen-key filter preamps
Lovepedal Eternity
Phase 100
Brown source
Fuzz Face
Flipster
Alembic F2B (tube preamp)
Opamp and FET buffers
Loads of speakercabinets and ampracks
Busy building a modular synth (ssm2044 vcfs, preamps, ADSR's, VCO's, VCA's)
Tables
Bookshelves
Basses
So many things! :D
Location: Rosmalen, NL
Has thanked: 27 times
Been thanked: 79 times

Post by Jarno »

I use a fuckton of these in my modulair synth (not push pull though), no problems at all.
And contact cleaner in a virtually new pot?
"It crackles....., but that's ok"

User avatar
CHEEZOR
Diode Debunker
Information
Posts: 831
Joined: 10 Jul 2009, 18:19
Location: California
Has thanked: 42 times
Been thanked: 50 times

Post by CHEEZOR »

rocklander wrote:
Blitz Krieg wrote:bourns?
lolbou wrote:Overheated?
[ Image ]
I see what you did there. :lol:

User avatar
mildew
Information
Posts: 40
Joined: 01 Jan 2015, 00:50
Has thanked: 1 time
Been thanked: 1 time

Post by mildew »

An update - retailer sent me a replacement for the first faulty pot.

the replacement lasted about a month before it went faulty like the other two, so i put the prs audio taper push/pull tone pot back in as a volume and it works perfectly.

so out of three alpha pushpulls, one lasted a week and the other two about a month.

they were the only pots ive ever had fail that couldnt be fixed with a squirt of contact cleaner - ive got guitars from the 80's where the pots are still fine.

I used the same 25w soldering iron the i use for everything else - these three alpha pushpulls are the first pots ive ever had fail.

User avatar
phatt
Transistor Tuner
Information
Posts: 1224
Joined: 04 Aug 2010, 05:17
Location: Morayfield SE Qld AU
Has thanked: 8 times
Been thanked: 343 times

Post by phatt »

Not sure what has happened here but worth a note of caution;
Those pots are quite delicate, the weak link is those tiny rivets that hold the lugs. The connection between lugs and pads is only via contact pressure of rivet so just bending those solder lugs can make the connection intermittent and as mentioned overheating will weaken the rivet pressure on the joint.

If the lug can be moved from side to side then the rivet has lost it's grip and a high chance you will have trouble. I've revived a few simply by repressing the rivets. (Delicately of course)

If the pot is just scratchy then that is the pad to wiper connection failing or dirty, cleaner may help for a while but I've found if you have it apart you may as well replace it.

FWIW, I wrap a short piece of masking tape around the outside of the back cover which helps to keep blobs of solder and crap out of the working internal parts.
It also stops small insect critters from setting up house,,, you would be surprised where critters find homes :shock:
Hope it helps, Phil.

User avatar
deltafred
Opamp Operator
Information
Posts: 1654
Joined: 06 Apr 2010, 16:16
Location: England
Has thanked: 813 times
Been thanked: 306 times

Post by deltafred »

Pots sometimes fail through no fault of their own!

Image
Politics is the art of so plucking the goose as to obtain the most feathers with the least squawking. - R.G. 2011
Jeez, she's an ugly bastard, she makes my socks hurt. I hope it's no ones missus here. - Ice-9 2012

User avatar
lolbou
Old Solderhand
Information
Posts: 2617
Joined: 18 Nov 2008, 21:38
Has thanked: 307 times
Been thanked: 225 times

Post by lolbou »

mildew wrote:An update - retailer sent me a replacement for the first faulty pot.

the replacement lasted about a month before it went faulty like the other two
Are these from different batches?

I would try both a different batch and a different man holding the iron. That would help finding whose fault it is... :wink:
- Are you a mod or a rocker?
- Uh, no, I'm a mocker.

User avatar
Dirk_Hendrik
Old Solderhand
Information
Posts: 4189
Joined: 03 Jul 2007, 08:44
Location: Old Amsterdam
Has thanked: 232 times
Been thanked: 886 times
Contact:

Post by Dirk_Hendrik »

Thanks Fred...

Now I have to clean the coffee spattered on my screen and dripping out of my nose.... :roll:
Sorry. Plain out of planes.

http://www.dirk-hendrik.com

User avatar
deltafred
Opamp Operator
Information
Posts: 1654
Joined: 06 Apr 2010, 16:16
Location: England
Has thanked: 813 times
Been thanked: 306 times

Post by deltafred »

That was from a Strat that our guitarist bought very cheap, he asked me if I could have a look at it!

The switch worked after a clean but the pots went straight into the bin. It had an expensive set of pickups in that were worth several times what he'd paid for the whole guitar. They are now in one of his gigging guitars and some cheap ass pups went into that one.
Politics is the art of so plucking the goose as to obtain the most feathers with the least squawking. - R.G. 2011
Jeez, she's an ugly bastard, she makes my socks hurt. I hope it's no ones missus here. - Ice-9 2012

User avatar
DrNomis
Old Solderhand
Information
Posts: 6804
Joined: 16 Jul 2009, 04:56
my favorite amplifier: Self-Built Valve Amp Head :)
Completed builds: Dallas Arbiter Fuzz Face,Tone Bender Professional Mk 3,Tone Bender 3-Knob,Baja BK Butler Tube Driver,Baja Real Tube Overdrive,Roger Mayer Octavia,EH Soul Preacher,Tech 21 XXL Distortion,MFOS Weird Sound Generator.
Location: Darwin,Northern Territory Australia
Has thanked: 98 times
Been thanked: 275 times

Post by DrNomis »

To be honest, I've never had a pot fail on me by going short-circuit, the ones that have failed on me have always gone open-circuit, there's at least two failure-modes I've seen in pots so far:


1, The solder lugs go lose where they're riveted to the resistive carbon track ends, and wiper connection on the phenolic substrate, the funny thing is I've noticed that certain values of pots seem to be more susceptible to this failure-mode than other values, the riveted joints tend to go lose due to heat-stress from overheating when soldering.


2,The carbon coating on the resistive track Flakes-off, due to the age of the pot or just mechanical wear, sometimes the flaking is enough to render the carbon track open-circuit.


My two cents worth..... :thumbsup
Genius is not all about 99% perspiration, and 1% inspiration - sometimes the solution is staring you right in the face.-Frequencycentral.

User avatar
astrobass
Cap Cooler
Information
Posts: 548
Joined: 02 Mar 2013, 01:30
Has thanked: 42 times
Been thanked: 74 times

Post by astrobass »

I've had the same experience as DrNomis. And I've never had a pot fail that wasn't particularly old or subjected to a clearly excessive amount of mechanical wear.

User avatar
Fender3D
Cap Cooler
Information
Posts: 573
Joined: 08 Aug 2009, 02:40
Location: Helltaly
Has thanked: 121 times
Been thanked: 153 times

Post by Fender3D »

Well,
I repaired a guitar which pot's solder lugs shorted to the shielding coating...

no pot's fault, of course...

User avatar
Ice-9
Degoop Doctor
Information
Posts: 1094
Joined: 31 Mar 2009, 15:29
my favorite amplifier: Marshall
Completed builds: Far to many to afford the enclosures for them all. :)
Has thanked: 134 times
Been thanked: 359 times
Contact:

Post by Ice-9 »

deltafred wrote:Pots sometimes fail through no fault of their own!

[ Image ]
Jeez, WTF that's a nuclear meltdown, ohh yeah baby ! (in an Austin Powers voice)
It's fairly straight forward, if you want to start it , press start. You can work out the rest of the controls for yourself !

No silicon heaven ? preposterous ! Where would all the calculators go ?

User avatar
mildew
Information
Posts: 40
Joined: 01 Jan 2015, 00:50
Has thanked: 1 time
Been thanked: 1 time

Post by mildew »

I must apologise to Alpha for bagging their pots, turns out the "Alphas" that i purchased from realtone music were fakes - no date or manufacturer codes.

dont buy from realtone, some of what they sell is fake.

User avatar
lolbou
Old Solderhand
Information
Posts: 2617
Joined: 18 Nov 2008, 21:38
Has thanked: 307 times
Been thanked: 225 times

Post by lolbou »

Good to know, thanks for the feedback! :thumbsup
- Are you a mod or a rocker?
- Uh, no, I'm a mocker.

Post Reply