Germanium diodes- the definitive answer

Frequent question abouts LED and other types of diodes.
User avatar
darkstar
Information
Posts: 34
Joined: 30 Jun 2011, 23:40
Has thanked: 4 times

Post by darkstar »

1)Ok so Ive searched round the not and ive found half people saying how much smoother they are than silicons and half people saying these are the harshest and LEDs are the smoothest. who is right?!?!?!?!?

2)i know they clip earlier. i have also found some people saying they have more distortion than silicons and some people saying less. who is right?!?!?

User avatar
culturejam
Old Solderhand
Information
Posts: 4062
Joined: 24 Feb 2008, 05:59
Has thanked: 433 times
Been thanked: 563 times
Contact:

Post by culturejam »

Moved.

And now I'll answer:

I think it depends on the circuit. But usually LEDs are a little harsher, at least to my ears. Sometimes that works well, and sometimes not.

Germanium clips more than silicon or LED. So it's going to naturally produce more compression and it will sound more "distorted". It's also going to result in less output volume.

User avatar
DrNomis
Old Solderhand
Information
Posts: 6807
Joined: 16 Jul 2009, 04:56
my favorite amplifier: Self-Built Valve Amp Head :)
Completed builds: Dallas Arbiter Fuzz Face,Tone Bender Professional Mk 3,Tone Bender 3-Knob,Baja BK Butler Tube Driver,Baja Real Tube Overdrive,Roger Mayer Octavia,EH Soul Preacher,Tech 21 XXL Distortion,MFOS Weird Sound Generator.
Location: Darwin,Northern Territory Australia
Has thanked: 98 times
Been thanked: 278 times

Post by DrNomis »

darkstar wrote:1)Ok so Ive searched round the not and ive found half people saying how much smoother they are than silicons and half people saying these are the harshest and LEDs are the smoothest. who is right?!?!?!?!?

2)i know they clip earlier. i have also found some people saying they have more distortion than silicons and some people saying less. who is right?!?!?

It really depends on where the diodes are connected in the circuit, if you have two Ge diodes as back-to-back clippers with an op-amp, they should clip smoothly and gradually, here's a couple of pics of diode clipping as seen on an oscilloscope,note the difference in the sharpness of the clipping:
Attachments
Germanium Diode Bridge Rectifier Clipping
Germanium Diode Bridge Rectifier Clipping
Silicon Diode Bridge Rectifier Clipping
Silicon Diode Bridge Rectifier Clipping
Genius is not all about 99% perspiration, and 1% inspiration - sometimes the solution is staring you right in the face.-Frequencycentral.

User avatar
Duckman
Opamp Operator
Information
Posts: 1492
Joined: 20 May 2009, 01:45
Has thanked: 320 times
Been thanked: 134 times

Post by Duckman »

Tested on the same circuit, I tend to hear from a very triangular wave and lower volume (Ge) through a intermediate between triangular and square with an acceptable volume (Si) up to a nearly square with the volume boosted (LED ).
Very subjective at the waveform, I know, but I always have this image in mind. :scratch:

User avatar
darkstar
Information
Posts: 34
Joined: 30 Jun 2011, 23:40
Has thanked: 4 times

Post by darkstar »

awesome thanks guys

User avatar
RnFR
Old Solderhand
Information
Posts: 4879
Joined: 09 Jan 2008, 06:02
my favorite amplifier: Traynor YBA-III, Fender Super Six
Completed builds: custom fuzz.
Location: Inner Earth
Has thanked: 139 times
Been thanked: 133 times
Contact:

Post by RnFR »

I'm sure this is already on the forum somewhere, but-

Ge diodes have the lowest forward voltage drop(Vf)(.3V vs. .6V for Si), which means with the same input signal, the diodes will conduct sooner and you will hear more distortion, and less output. you can remedy this by putting them in series. they also have the roundest conduction knee, which you can see in the smoother wave above. this makes them sound smoother than the others. LEDs have a very high voltage drop(depends on color), letting the circuit sound louder, but they also have a harsher knee. this all usually just comes down to personal preference. one of the fun things a beginner can do is buy a bunch of different types of diodes and fool around with them, mixing and matching til your heart's content.
"You've converted me to Cubic thinking. Where do I sign up for the newsletter? I need to learn more about how I can break free from ONEism Death Math." - Soulsonic

Blog-APOCALYPSE AUDIO

User avatar
asatbluesboy
Breadboard Brother
Information
Posts: 53
Joined: 31 Mar 2010, 13:50
Has thanked: 38 times
Been thanked: 1 time

Post by asatbluesboy »

LED will be the harshest of all, and Ge has the less output (as already pointed out by many). Si vs LED is pretty much RAT vs Turbo RAT.
...collectors together and emitter to base? You're such a darling...

ton.

User avatar
emakris
Breadboard Brother
Information
Posts: 57
Joined: 06 Aug 2010, 23:25

Post by emakris »

DrNomis wrote:
darkstar wrote:1)Ok so Ive searched round the not and ive found half people saying how much smoother they are than silicons and half people saying these are the harshest and LEDs are the smoothest. who is right?!?!?!?!?

2)i know they clip earlier. i have also found some people saying they have more distortion than silicons and some people saying less. who is right?!?!?

It really depends on where the diodes are connected in the circuit, if you have two Ge diodes as back-to-back clippers with an op-amp, they should clip smoothly and gradually, here's a couple of pics of diode clipping as seen on an oscilloscope,note the difference in the sharpness of the clipping:
DrNomis, what is your circuit setup? What kind of signal are you running through them in these pictures?
currently persona non grata here

User avatar
GuitarlCarl
Cap Cooler
Information
Posts: 614
Joined: 14 Dec 2010, 15:14
my favorite amplifier: anything tube
Completed builds: Ds-1 mods, SD-1 mods, Small Clone mods, Muff build, Axis build, various other transistor booster builds... I can build a badaxe harmonic perc, but I can't get a fuzzface to sound worth a crap!
Location: Smellinoiz
Has thanked: 54 times
Been thanked: 29 times

Post by GuitarlCarl »

Trade secret from china dude... then we gooped it.
I want it to sound like bees buzzing around in a 55 gallon drum...

User avatar
DrNomis
Old Solderhand
Information
Posts: 6807
Joined: 16 Jul 2009, 04:56
my favorite amplifier: Self-Built Valve Amp Head :)
Completed builds: Dallas Arbiter Fuzz Face,Tone Bender Professional Mk 3,Tone Bender 3-Knob,Baja BK Butler Tube Driver,Baja Real Tube Overdrive,Roger Mayer Octavia,EH Soul Preacher,Tech 21 XXL Distortion,MFOS Weird Sound Generator.
Location: Darwin,Northern Territory Australia
Has thanked: 98 times
Been thanked: 278 times

Post by DrNomis »

emakris wrote:
DrNomis wrote:
darkstar wrote:1)Ok so Ive searched round the not and ive found half people saying how much smoother they are than silicons and half people saying these are the harshest and LEDs are the smoothest. who is right?!?!?!?!?

2)i know they clip earlier. i have also found some people saying they have more distortion than silicons and some people saying less. who is right?!?!?

It really depends on where the diodes are connected in the circuit, if you have two Ge diodes as back-to-back clippers with an op-amp, they should clip smoothly and gradually, here's a couple of pics of diode clipping as seen on an oscilloscope,note the difference in the sharpness of the clipping:
DrNomis, what is your circuit setup? What kind of signal are you running through them in these pictures?

It's actually a really simple setup, I just arranged the Silicon Diodes and Germanium Transistors (used as Diodes) as per the diagram below on my breadboard:

You might recognize the Diode Configuration as that used by Marshall in their JCM 800 and 900 Amps.

Note:As it says in the diagram, I set the signal generator to produce a 1kHz Sinewave , and adjusted the output till it caused the diodes to clip the signal-peaks.... :thumbsup
Attachments
Diode Clipper Breadboard Schematic
Diode Clipper Breadboard Schematic
Genius is not all about 99% perspiration, and 1% inspiration - sometimes the solution is staring you right in the face.-Frequencycentral.

User avatar
emakris
Breadboard Brother
Information
Posts: 57
Joined: 06 Aug 2010, 23:25

Post by emakris »

DrNomis wrote:
emakris wrote:
DrNomis wrote:
darkstar wrote:1)Ok so Ive searched round the not and ive found half people saying how much smoother they are than silicons and half people saying these are the harshest and LEDs are the smoothest. who is right?!?!?!?!?

2)i know they clip earlier. i have also found some people saying they have more distortion than silicons and some people saying less. who is right?!?!?

It really depends on where the diodes are connected in the circuit, if you have two Ge diodes as back-to-back clippers with an op-amp, they should clip smoothly and gradually, here's a couple of pics of diode clipping as seen on an oscilloscope,note the difference in the sharpness of the clipping:
DrNomis, what is your circuit setup? What kind of signal are you running through them in these pictures?

It's actually a really simple setup, I just arranged the Silicon Diodes and Germanium Transistors (used as Diodes) as per the diagram below on my breadboard:

You might recognize the Diode Configuration as that used by Marshall in their JCM 800 and 900 Amps.

Note:As it says in the diagram, I set the signal generator to produce a 1kHz Sinewave , and adjusted the output till it caused the diodes to clip the signal-peaks.... :thumbsup
Drnomis, thank you. I honestly wasn't sure if you would answer and share with me of all people, and I'm glad you did. Again, thank you.
currently persona non grata here

User avatar
DrNomis
Old Solderhand
Information
Posts: 6807
Joined: 16 Jul 2009, 04:56
my favorite amplifier: Self-Built Valve Amp Head :)
Completed builds: Dallas Arbiter Fuzz Face,Tone Bender Professional Mk 3,Tone Bender 3-Knob,Baja BK Butler Tube Driver,Baja Real Tube Overdrive,Roger Mayer Octavia,EH Soul Preacher,Tech 21 XXL Distortion,MFOS Weird Sound Generator.
Location: Darwin,Northern Territory Australia
Has thanked: 98 times
Been thanked: 278 times

Post by DrNomis »

emakris wrote:
DrNomis wrote:
emakris wrote:
DrNomis wrote:
darkstar wrote:1)Ok so Ive searched round the not and ive found half people saying how much smoother they are than silicons and half people saying these are the harshest and LEDs are the smoothest. who is right?!?!?!?!?

2)i know they clip earlier. i have also found some people saying they have more distortion than silicons and some people saying less. who is right?!?!?

It really depends on where the diodes are connected in the circuit, if you have two Ge diodes as back-to-back clippers with an op-amp, they should clip smoothly and gradually, here's a couple of pics of diode clipping as seen on an oscilloscope,note the difference in the sharpness of the clipping:
DrNomis, what is your circuit setup? What kind of signal are you running through them in these pictures?

It's actually a really simple setup, I just arranged the Silicon Diodes and Germanium Transistors (used as Diodes) as per the diagram below on my breadboard:

You might recognize the Diode Configuration as that used by Marshall in their JCM 800 and 900 Amps.

Note:As it says in the diagram, I set the signal generator to produce a 1kHz Sinewave , and adjusted the output till it caused the diodes to clip the signal-peaks.... :thumbsup
Drnomis, thank you. I honestly wasn't sure if you would answer and share with me of all people, and I'm glad you did. Again, thank you.

No worries, I'm only too happy to share with anyone, all circuit diagrams and other stuff I post is posted for the benefit of everyone here in freestompboxes.org, in the spirit of DIY..... :thumbsup
Genius is not all about 99% perspiration, and 1% inspiration - sometimes the solution is staring you right in the face.-Frequencycentral.

User avatar
DrNomis
Old Solderhand
Information
Posts: 6807
Joined: 16 Jul 2009, 04:56
my favorite amplifier: Self-Built Valve Amp Head :)
Completed builds: Dallas Arbiter Fuzz Face,Tone Bender Professional Mk 3,Tone Bender 3-Knob,Baja BK Butler Tube Driver,Baja Real Tube Overdrive,Roger Mayer Octavia,EH Soul Preacher,Tech 21 XXL Distortion,MFOS Weird Sound Generator.
Location: Darwin,Northern Territory Australia
Has thanked: 98 times
Been thanked: 278 times

Post by DrNomis »

There's also this screenshot of Led Clipping on my Oscilloscope, with the same breadboard setup as for the other two screenshots, except this time the diodes are Leds of course:
Attachments
Led Bridge Rectifier Clipping
Led Bridge Rectifier Clipping
Genius is not all about 99% perspiration, and 1% inspiration - sometimes the solution is staring you right in the face.-Frequencycentral.

User avatar
RnFR
Old Solderhand
Information
Posts: 4879
Joined: 09 Jan 2008, 06:02
my favorite amplifier: Traynor YBA-III, Fender Super Six
Completed builds: custom fuzz.
Location: Inner Earth
Has thanked: 139 times
Been thanked: 133 times
Contact:

Post by RnFR »

there are other things that go into the difference of Ge diodes vs. others as well. leakage and capacitance being two of them.
"You've converted me to Cubic thinking. Where do I sign up for the newsletter? I need to learn more about how I can break free from ONEism Death Math." - Soulsonic

Blog-APOCALYPSE AUDIO

User avatar
deltafred
Opamp Operator
Information
Posts: 1654
Joined: 06 Apr 2010, 16:16
Location: England
Has thanked: 813 times
Been thanked: 306 times

Post by deltafred »

DrNomis wrote:There's also this screenshot of Led Clipping on my Oscilloscope, with the same breadboard setup as for the other two screenshots, except this time the diodes are Leds of course:
Are you sure you have the correct photo there, that looks awfully like a sine wave to me?
Politics is the art of so plucking the goose as to obtain the most feathers with the least squawking. - R.G. 2011
Jeez, she's an ugly bastard, she makes my socks hurt. I hope it's no ones missus here. - Ice-9 2012

User avatar
mictester
Old Solderhand
Information
Posts: 2923
Joined: 11 Sep 2008, 20:29
my favorite amplifier: Mesa Boogie, Roost Sessionmaster, AC30
Completed builds: Hundreds! Mostly originals, a few clones and lots of modifications.
Location: Somewhat closer to Amsterdam than before!
Has thanked: 32 times
Been thanked: 844 times
Contact:

Post by mictester »

RnFR wrote:there are other things that go into the difference of Ge diodes vs. others as well. leakage and capacitance being two of them.
The capacitance tends to only be a few pF, so won't have a significant effect at audio frequencies. However, leakage can have a significant effect, as can temperature (that's GERMANIUM Lance). There's also quite a wide spread in forward voltage drop against current with germanium diodes so asymmetry is often inherent!
"Why is it humming?" "Because it doesn't know the words!"

User avatar
DrNomis
Old Solderhand
Information
Posts: 6807
Joined: 16 Jul 2009, 04:56
my favorite amplifier: Self-Built Valve Amp Head :)
Completed builds: Dallas Arbiter Fuzz Face,Tone Bender Professional Mk 3,Tone Bender 3-Knob,Baja BK Butler Tube Driver,Baja Real Tube Overdrive,Roger Mayer Octavia,EH Soul Preacher,Tech 21 XXL Distortion,MFOS Weird Sound Generator.
Location: Darwin,Northern Territory Australia
Has thanked: 98 times
Been thanked: 278 times

Post by DrNomis »

deltafred wrote:
DrNomis wrote:There's also this screenshot of Led Clipping on my Oscilloscope, with the same breadboard setup as for the other two screenshots, except this time the diodes are Leds of course:
Are you sure you have the correct photo there, that looks awfully like a sine wave to me?

Yes, it is, I had to turn-up the output level of the signal generator quite a bit to get the Leds to clip the signal as much as shown in the screenshot, the Leds were at full brightness when I took that screenshot pic(5 Red 5mm Leds were used)..... :thumbsup


Leds actually have a soft turn-on characteristic which is similar to Germanium diodes, except that the forward voltage drop for a Led is much greater than a Germanium diode, hence the reason why the signal still looks relatively Sinewave-like even at high signal levels...... :thumbsup
Genius is not all about 99% perspiration, and 1% inspiration - sometimes the solution is staring you right in the face.-Frequencycentral.

User avatar
DrNomis
Old Solderhand
Information
Posts: 6807
Joined: 16 Jul 2009, 04:56
my favorite amplifier: Self-Built Valve Amp Head :)
Completed builds: Dallas Arbiter Fuzz Face,Tone Bender Professional Mk 3,Tone Bender 3-Knob,Baja BK Butler Tube Driver,Baja Real Tube Overdrive,Roger Mayer Octavia,EH Soul Preacher,Tech 21 XXL Distortion,MFOS Weird Sound Generator.
Location: Darwin,Northern Territory Australia
Has thanked: 98 times
Been thanked: 278 times

Post by DrNomis »

I need to go see the people at Territory Housing for a couple of things today, when I get back home I'll breadboard a simple Op-Amp circuit with 2 back-to-back clipping diodes and post some new screenshots in this forum thread, so please stay tuned..... :thumbsup
Genius is not all about 99% perspiration, and 1% inspiration - sometimes the solution is staring you right in the face.-Frequencycentral.

User avatar
Greg
Old Solderhand
Information
Posts: 3047
Joined: 03 Nov 2007, 09:35
my favorite amplifier: Tophat Emplexador & Supreme 16.
Completed builds: LOTS..
Location: Australia
Has thanked: 65 times
Been thanked: 164 times

Post by Greg »

I say Germaniums tend to sound sound harsher.. even at the same clipping threshold.
What we see on a scope and what our ears perceive are 2 different things.
culturejam wrote: We are equal opportunity exposure artists.

User avatar
DrNomis
Old Solderhand
Information
Posts: 6807
Joined: 16 Jul 2009, 04:56
my favorite amplifier: Self-Built Valve Amp Head :)
Completed builds: Dallas Arbiter Fuzz Face,Tone Bender Professional Mk 3,Tone Bender 3-Knob,Baja BK Butler Tube Driver,Baja Real Tube Overdrive,Roger Mayer Octavia,EH Soul Preacher,Tech 21 XXL Distortion,MFOS Weird Sound Generator.
Location: Darwin,Northern Territory Australia
Has thanked: 98 times
Been thanked: 278 times

Post by DrNomis »

Greg_G wrote:I say Germaniums tend to sound sound harsher.. even at the same clipping threshold.
What we see on a scope and what our ears perceive are 2 different things.

That's true, the Oscilloscope has a bandwidth that's quite a few orders of magnitude wider than the human ear, my Scope can go from DC to 20Mhz, a young healthy ear can go from 20hz to 20kHz, as we age we lose the high-end response of our ears naturally due to aging, or excessive loud noise exposure, what we see on a Scope screen is really a graph of Voltage versus Time, to see the individual harmonics, we need a Spectrum Analyser, wish I had one.... :hmmm:

It's interesting how our ears are able to hear the harmonics of a signal as a perceived Timbral-Colour.... :hmmm:
Genius is not all about 99% perspiration, and 1% inspiration - sometimes the solution is staring you right in the face.-Frequencycentral.

Post Reply