Bearfoot - Baby Pink Booster [traced]
Posted: 20 Mar 2013, 05:02
freestompboxes.org
tracing pedals since 2007
https://www.freestompboxes.org/
Bearfoot - Baby Pink Booster
Page 1 of 1
Re: Bearfoot Baby Pink Booster
Posted: 20 Mar 2013, 15:02
That unnecessarily huge cap must be where all the awesome is stored. 
Re: Bearfoot Baby Pink Booster
Posted: 20 Mar 2013, 16:02
Love the quickies 
Re: Bearfoot Baby Pink Booster
Posted: 21 Mar 2013, 00:56
And here's a PCB. Parts match the schem, and I don't think I need to say no commercial use, but no commercial use. Print at 300dpi.
Re: Bearfoot Baby Pink Booster
Posted: 21 Mar 2013, 01:17
And here's one with larger pad sizes. Figured I'd make it a bit easier for less experienced etchers.
Re: Bearfoot Baby Pink Booster
Posted: 21 Mar 2013, 07:51
Would above PCB be processed?
Re: Bearfoot Baby Pink Booster
Posted: 21 Mar 2013, 12:11
Would you please stop spamming the DIY electronics forums? Thank you.real-pcb wrote:Would above PCB be processed?
Re: Bearfoot Baby Pink Booster
Posted: 21 Mar 2013, 15:06
No it needs to be coagulated.real-pcb wrote:Would above PCB be processed?
Re: Bearfoot Baby Pink Booster
Posted: 21 Mar 2013, 18:38
so switch is wired so that the thing is still a buffer when it's off. For regular operation regular switch wiring, right?
Re: Bearfoot Baby Pink Booster
Posted: 21 Mar 2013, 18:41
Yup. If you want to wire it as true bypass, dump the 150k resistor at the cold lug of the boost pot and leave the wiper connected to ground.Seiche wrote:so switch is wired so that the thing is still a buffer when it's off. For regular operation regular switch wiring, right?
Re: Bearfoot Baby Pink Booster
Posted: 28 Mar 2013, 13:52
looking at the pcb again, this looks like it could be the same pcb used on the candy apple fuzz (as usual for the Bearfoots). This might be a good opportunity to trace out the pcb connections, as the traces are easily visible to facilitate tracing of the CAF once it's released.
Re: Bearfoot Baby Pink Booster
Posted: 28 Mar 2013, 17:43
people pay for this?
Re: Bearfoot Baby Pink Booster
Posted: 28 Mar 2013, 18:56
well it's pretty darn cute 
Re: Bearfoot Baby Pink Booster
Posted: 28 Mar 2013, 21:38
Seiche has been waiting to unload that Reese photo!
Re: Bearfoot Baby Pink Booster
Posted: 29 Mar 2013, 23:04
It's used in the CAF and EGD. Was gonna buy an EGD, but I've kinda lost interest.Seiche wrote:looking at the pcb again, this looks like it could be the same pcb used on the candy apple fuzz (as usual for the Bearfoots). This might be a good opportunity to trace out the pcb connections, as the traces are easily visible to facilitate tracing of the CAF once it's released.
Re: Bearfoot - Baby Pink Booster
Posted: 27 Aug 2017, 19:19
Excuse me:D1,D2,D3 is 1n4002?
As far away as China
As far away as China
Re: Bearfoot - Baby Pink Booster
Posted: 17 Sep 2017, 08:08
laoliang wrote:Excuse me:I'm ready, but no sound, I checked again and again, my triode in 5458
Re: Bearfoot Baby Pink Booster
Posted: 22 Jun 2018, 07:47
Can someone explain what is happening here? I just left the 150k in the circuit and wired the bypass as usual. What's the difference? When turned all the way down, the signal is at unity gain.mmolteratx wrote:If you want to wire it as true bypass, dump the 150k resistor at the cold lug of the boost pot and leave the wiper connected to ground.
No, D2 is a zener for LED protection, D3 is an LED. I left D2, D3 off my build as I did not use the buffered bypass.laoliang wrote:Excuse me:D1,D2,D3 is 1n4002?
As far away as China