smallsound/bigsound Team Awesome! Fuzz Machine [traced]
So I found these pictures on the ss/bs blog, located here: http://smallsoundbigsound.blogspot.com/ ... -work.html
The pictures should give someone a good start, and the other image should give all of the part values. I'm not sure what the changes were between versions. I tried my hand at figuring this out, but didn't make it too far. I figure I'll leave it to someone more experienced. There are some more pictures on the blog that I haven't attached.
The pictures should give someone a good start, and the other image should give all of the part values. I'm not sure what the changes were between versions. I tried my hand at figuring this out, but didn't make it too far. I figure I'll leave it to someone more experienced. There are some more pictures on the blog that I haven't attached.
- skywise
- Breadboard Brother
You could probably ask Brian some details about the circuit. He seems like the kind of guy that would be down to share. He's an actual DIY guy, not a razzle-dazzle boutique douche.
yeah that version is OLD! i think the newer one is better, but some folks' opinions differ with mine.
the details are pretty simple - split the signal, fuzz one side, mix them together - there are endless variations on the theme.
the details are pretty simple - split the signal, fuzz one side, mix them together - there are endless variations on the theme.
- Bill_Mountain
- Breadboard Brother
The endless variations is what gets me. Every time I think I've designed the ultimate fuzz (for me), I start going, "...well what if I do this? What about this? Maybe I can use some boutiquey mod's here? Maybe I can replace this BJT with an FET..."smallsnd/bigsnd wrote:yeah that version is OLD! i think the newer one is better, but some folks' opinions differ with mine.
the details are pretty simple - split the signal, fuzz one side, mix them together - there are endless variations on the theme.
How did you get to the end and say, "I'm finished!"
Honestly I don't think I ever will.
that's quite the philosophical query. i usually go with my instincts and personal taste though i've been through roughly 6-7 revisions with the TAFM (subtle tweaks), so i guess i will never be finished either...Bill_Mountain wrote:
The endless variations is what gets me. Every time I think I've designed the ultimate fuzz (for me), I start going, "...well what if I do this? What about this? Maybe I can use some boutiquey mod's here? Maybe I can replace this BJT with an FET..."
How did you get to the end and say, "I'm finished!"
Honestly I don't think I ever will.
- MoonWatcher
- Diode Debunker
I like that the attention has been put on a clean layout as opposed to having some kind of fancy capacitors on there. Just regular electrolytics and a few types of ceramics if I'm seeing things right.
I know it could be argued that with fuzz you don't need "audiophile grade" caps, but just the same - it's cool to see.
I'm sick of seeing stuff with Panasonic metalized film caps, or even the old school approach of cramming some monster Mallory 150 high voltage type axial caps just for the el-bling-o factor.
I got to work on a few 1st gen 90's Marshall pedals for a friend, and I overall liked the emphasis on layout vs. "premium component" choices. The pcb's shown in this thread remind me of them.
I know it could be argued that with fuzz you don't need "audiophile grade" caps, but just the same - it's cool to see.
I'm sick of seeing stuff with Panasonic metalized film caps, or even the old school approach of cramming some monster Mallory 150 high voltage type axial caps just for the el-bling-o factor.
I got to work on a few 1st gen 90's Marshall pedals for a friend, and I overall liked the emphasis on layout vs. "premium component" choices. The pcb's shown in this thread remind me of them.
thanks! that's pretty much where i'm at.MoonWatcher wrote:I like that the attention has been put on a clean layout as opposed to having some kind of fancy capacitors on there. Just regular electrolytics and a few types of ceramics if I'm seeing things right. I overall liked the emphasis on layout vs. "premium component" choices. The pcb's shown in this thread remind me of them.
I've got a more recent version of this pedal. The PCBs are marked "v6.2 2012". It's quite different to the boards posted above.
I went ahead and attempted a trace of it. The IO board is a nice little design; it's a Brass Master descendant with some added spice.
I'm pretty confident in what I've drawn, but I welcome any questions or corrections!
Important note: most of the capacitor values are different from what's marked on the PCB silkscreens. It makes me question the pot values a little.
I went ahead and attempted a trace of it. The IO board is a nice little design; it's a Brass Master descendant with some added spice.
I'm pretty confident in what I've drawn, but I welcome any questions or corrections!
Important note: most of the capacitor values are different from what's marked on the PCB silkscreens. It makes me question the pot values a little.
pretty close for the most part. think brassmaster + tweaked fuzzface with tone control.
this was from an NPN revision and i've since gone back to using PNP with an LT1054 due to the very inconsistent nature of NPN germaniums. too much of a headache.
also, small tweaks since that version which gave slightly wider range to the gain and tone control. tiny resistor/cap tweaks which could be adjusted for taste for anyone seeking to build. pot values are generally 100K/gain, 10kA/clean, 10kA/wet, 5kC/fuzz, 25k/shape.
this was from an NPN revision and i've since gone back to using PNP with an LT1054 due to the very inconsistent nature of NPN germaniums. too much of a headache.
also, small tweaks since that version which gave slightly wider range to the gain and tone control. tiny resistor/cap tweaks which could be adjusted for taste for anyone seeking to build. pot values are generally 100K/gain, 10kA/clean, 10kA/wet, 5kC/fuzz, 25k/shape.
- johnk
- Resistor Ronker
i own the original SS/BS PNP version (that also has two internal trimpots) and built the NPN version posted here. it works and sounds great, but the gate doesn't work like the original. it does affect the nature and sound of the fuzz but it doesn't gate. any ideas about that?
I looked over the connections to the Gate switch again, and the schematic above still seems right...But now I'm doubting myself.
Try checking the transistor voltages on the fuzz board. Here are the readings from my unit:
All controls at minimum, pedal bypassed, Gate switch OFF:
Q1: C = 0.31V B = 0.10V E = 0V
Q2: C = 7.92V B = 0.31V E = 0.25V
All controls at minimum, pedal bypassed, Gate switch ON:
Q1: C = 0.16V B = 0.05V E = 0V
Q2: C = 0.07V B = 0.16V E = 0V
Try checking the transistor voltages on the fuzz board. Here are the readings from my unit:
All controls at minimum, pedal bypassed, Gate switch OFF:
Q1: C = 0.31V B = 0.10V E = 0V
Q2: C = 7.92V B = 0.31V E = 0.25V
All controls at minimum, pedal bypassed, Gate switch ON:
Q1: C = 0.16V B = 0.05V E = 0V
Q2: C = 0.07V B = 0.16V E = 0V
did you get it going? those NPNs can be a bitch and the gate control works inconsistently - some values may need to be tweaked to get it working properly.johnk wrote:i own the original SS/BS PNP version (that also has two internal trimpots) and built the NPN version posted here. it works and sounds great, but the gate doesn't work like the original. it does affect the nature and sound of the fuzz but it doesn't gate. any ideas about that?
- johnk
- Resistor Ronker
yep. i socketed them so i just tried a different pair of germs and it works perfectly and sounds awesome! thanks!smallsnd/bigsnd wrote:did you get it going? those NPNs can be a bitch and the gate control works inconsistently - some values may need to be tweaked to get it working properly.johnk wrote:i own the original SS/BS PNP version (that also has two internal trimpots) and built the NPN version posted here. it works and sounds great, but the gate doesn't work like the original. it does affect the nature and sound of the fuzz but it doesn't gate. any ideas about that?
Information
- Posts: 11
- Joined: 27 Jul 2016, 10:47
- Completed builds: Shinei FY-2, D*A*M Meathead, Mid-Fi Electronics Deluxe Pitch Pirate, Clarinot, Demo Tape Fuzz, Random Number Generator, Wattson EFY-6, Smallsound/Bigsound Mini, DBA Reverberation Machine, Parasit Studio Raygun Youth, Vox Repeat Percussion, 1776 Multiplex Echo Machine, David Rolo Twin Peaks, Giant Hogweed, Devi Ever Soda Meiser, ZVEX Machine, SHO, Fat Fuzz Factory.
- Has thanked: 37 times
- Been thanked: 5 times
This might be a silly question, but what does the internal dip switch do?
- jrfox92
- Breadboard Brother
Information
- Posts: 70
- Joined: 11 Jun 2014, 04:46
- Completed builds: Death by Audio Fuzz War
Electro-Harmonix Big Muff Pi V5
Skreddy Lunar Module
Colorsound Overdriver
Electro-Harmonix Big Muff Pi Multi-Diode and Feedback Mod
Electro-Harmonix Holy Grail Room Reverb and Reverb Length Mod
Boss DS-1 Synth Circuit Bend - Location: Akron, Ohio
- Has thanked: 3 times
- Been thanked: 54 times
Adds/removes a Jfet-based input buffer.Addy Bart wrote:This might be a silly question, but what does the internal dip switch do?