BJFE-Baby Blue  [traced]

General documentation, gut shot, schematic links, ongoing circuit tracing, deep thoughts ... all about boutique stompboxes.

BJFE-Baby Blue

Postby momo lab » 02 Nov 2017, 19:20

Hi, everyone,My English is very bad,Sorry about this.

this is bjfe-baby blue od, wonderful od pedal,I hope the disassembly process goes well.

For now, I have a question,I do not know the type of this diode,It's big,The character is S 2A 1200.

When I finish, I will upload the detailed layout, thank you all.
1.jpg

2.jpg

3.jpg

4.jpg

5.jpg

6.jpg

7.jpg

8.jpg
You do not have the required permissions to view the files attached to this post.

For this message the author momo lab has received thanks: 6
dv8r601 (02 Nov 2017, 23:22), Greg (03 Nov 2017, 13:30), Intripped (04 Nov 2017, 14:16), Manfred (03 Nov 2017, 03:48), modman (02 Nov 2017, 20:56), schrumpfschlauch (03 Nov 2017, 08:03)
User avatar
momo lab
Degoop Doctor
 
Posts: 8
Joined: 25 Oct 2017, 12:49
Has thanked: 2 times
Have thanks: 23 times

Re: BJFE-Baby Blue

Postby toneman » 02 Nov 2017, 19:33

Looks like a schottky diode. Like ones used in switching power supplies. Has less voltage drop than a silicon diode.

Also Depends a little on where it is used in the circuit.

If it is in the clipping/clamping/feedback circuit, any schottky will probably work.
Maybe just try a good old 1N4148/1N914 (?)
8)
Tone-to-the-Bone

For this message the author toneman has received thanks:
momo lab (03 Nov 2017, 10:06)
User avatar
toneman
Resistor Ronker
 
Posts: 270
Joined: 17 Jul 2007, 14:05
Location: sacatomatoes, Kali4nia
Has thanked: 85 times
Have thanks: 19 times

Re: BJFE-Baby Blue

Postby Manfred » 03 Nov 2017, 04:17

You could measure the threshold voltage of the diode in this way:

diodetest.JPG


I do not see an OP-Amp Pin layout on the PCB shot.
Is there an OP-Amp installed or is this only a transitor circuit?
You do not have the required permissions to view the files attached to this post.

For this message the author Manfred has received thanks: 2
bajaman (03 Nov 2017, 10:02), momo lab (03 Nov 2017, 10:07)
Manfred
Resistor Ronker
 
Posts: 446
Joined: 05 Apr 2009, 00:42
Has thanked: 760 times
Have thanks: 338 times

Re: BJFE-Baby Blue

Postby momo lab » 03 Nov 2017, 10:19

This job is difficult and slow,I mean,Really slow.

The threshold for this diode is 0.536v and 0.523v,It does not use the OP-amp, but the use of a JFET,Very simple and effective circuit.

9.jpg


10.jpg
You do not have the required permissions to view the files attached to this post.

For this message the author momo lab has received thanks: 2
Manfred (03 Nov 2017, 10:34), modman (03 Nov 2017, 18:28)
User avatar
momo lab
Degoop Doctor
 
Posts: 8
Joined: 25 Oct 2017, 12:49
Has thanked: 2 times
Have thanks: 23 times

Re: BJFE-Baby Blue

Postby Manfred » 03 Nov 2017, 10:49

What are the dimensions of the PCB-Board?
Manfred
Resistor Ronker
 
Posts: 446
Joined: 05 Apr 2009, 00:42
Has thanked: 760 times
Have thanks: 338 times

Re: BJFE-Baby Blue

Postby momo lab » 04 Nov 2017, 12:55

Manfred wrote:What are the dimensions of the PCB-Board?

Its size is 55 * 22 mm, but its shape is irregular.
I have built an identical PCB plan,Although not perfect, but I am ready to use it,Suppose I copy the value of it.

11.JPG
You do not have the required permissions to view the files attached to this post.

For this message the author momo lab has received thanks: 3
anselm (05 Nov 2017, 13:42), Manfred (04 Nov 2017, 13:46), modman (07 Nov 2017, 11:59)
User avatar
momo lab
Degoop Doctor
 
Posts: 8
Joined: 25 Oct 2017, 12:49
Has thanked: 2 times
Have thanks: 23 times

Re: BJFE-Baby Blue

Postby Manfred » 09 Nov 2017, 17:02

This job is difficult and slow,I mean,Really slow.

I see, it is a tough piece of work, the tracing takes time.
Manfred
Resistor Ronker
 
Posts: 446
Joined: 05 Apr 2009, 00:42
Has thanked: 760 times
Have thanks: 338 times

Re: BJFE-Baby Blue

Postby momo lab » 11 Nov 2017, 14:35

Manfred wrote:
This job is difficult and slow,I mean,Really slow.

I see, it is a tough piece of work, the tracing takes time.

Sorry, a lot of work these days.
Schematic has been updated.

12.jpg


13.jpg
You do not have the required permissions to view the files attached to this post.

For this message the author momo lab has received thanks: 7
d312a (11 Nov 2017, 19:33), fuzzbunny (11 Nov 2017, 18:43), Greg (12 Nov 2017, 00:44), Manfred (11 Nov 2017, 20:31), modman (12 Nov 2017, 12:42), Nocentelli (11 Nov 2017, 16:22), Tuolotupa (11 Nov 2017, 21:45)
User avatar
momo lab
Degoop Doctor
 
Posts: 8
Joined: 25 Oct 2017, 12:49
Has thanked: 2 times
Have thanks: 23 times

Re: BJFE-Baby Blue

Postby momo lab » 11 Nov 2017, 21:41

I just updated the layout, and sprayed the shell ready to clone it, thank you all.

14.JPG


15.jpg


16.jpg
You do not have the required permissions to view the files attached to this post.
User avatar
momo lab
Degoop Doctor
 
Posts: 8
Joined: 25 Oct 2017, 12:49
Has thanked: 2 times
Have thanks: 23 times

Re: BJFE-Baby Blue

Postby fuzzbunny » 12 Nov 2017, 01:22

Thanks for your hard work!

Do you have any idea which JFETs the original circuit used? Any voltage readings on the original JFETs?

How about D3 & D4 ? What kind of diodes?
fuzzbunny
 
Posts: 24
Joined: 09 Jan 2012, 19:12
Has thanked: 5 times
Have thanks: 5 times

Re: BJFE-Baby Blue

Postby Manfred » 12 Nov 2017, 05:17

The FET-Stage circuits of the Baby Pink Booster and Model_H drive are similar to the Baby Blue FET-Stages,
where the 2N5952 FET is applied.

In my opinion R6 should by 22k not 220k as in the schematic shown.

BJFE applies often the 1N400X diodes as clipping diodes.
Manfred
Resistor Ronker
 
Posts: 446
Joined: 05 Apr 2009, 00:42
Has thanked: 760 times
Have thanks: 338 times

Re: BJFE-Baby Blue  [traced]

Postby momo lab » 12 Nov 2017, 08:44

BBOD.JPG
You do not have the required permissions to view the files attached to this post.

For this message the author momo lab has received thanks: 4
d312a (12 Nov 2017, 12:30), dv8r601 (13 Nov 2017, 09:03), Manfred (13 Nov 2017, 22:20), modman (12 Nov 2017, 12:41)
User avatar
momo lab
Degoop Doctor
 
Posts: 8
Joined: 25 Oct 2017, 12:49
Has thanked: 2 times
Have thanks: 23 times

Re: BJFE-Baby Blue

Postby momo lab » 13 Nov 2017, 14:25

fuzzbunny wrote:Thanks for your hard work!

Do you have any idea which JFETs the original circuit used? Any voltage readings on the original JFETs?

How about D3 & D4 ? What kind of diodes?

Manfred wrote:The FET-Stage circuits of the Baby Pink Booster and Model_H drive are similar to the Baby Blue FET-Stages,
where the 2N5952 FET is applied.

In my opinion R6 should by 22k not 220k as in the schematic shown.

BJFE applies often the 1N400X diodes as clipping diodes.


After I checked, R6 is indeed 22K, not 220K, 15K resistor should be 14.7K.
It uses diodes and JFETs I'm not sure, the diode has a clear character, S 2A 1200, but I do not know its model number.
After the measurement, the first stage FET voltage is 4.62V and 1.72V, the second stage FET voltage is 4.72 / 1.68 and the third stage is 5.55 / 1.44.

Earlier today, I tried to make a PCB and use it to test the BF244 as a JFET, frustrating that it did not work well, the gain was significantly lower, and the more frustrating thing was that I came from China, fake Very much, I'm not sure JFET in my hand is really BF244, in your country common 2NXXXX series I can not determine the hands of the real thing. I do not know where something went wrong, and now it's no longer sounding, ready to do a few more PCB tries, I will try to feedback in time, thanks again!

17.jpg


18.jpg
You do not have the required permissions to view the files attached to this post.
User avatar
momo lab
Degoop Doctor
 
Posts: 8
Joined: 25 Oct 2017, 12:49
Has thanked: 2 times
Have thanks: 23 times

Re: BJFE-Baby Blue

Postby Manfred » 13 Nov 2017, 22:44

I have done some calculations and found that the value R5 ist to high.
Please check it again, maybe is the value 14.7 Kohms not 47 kohms.

Cool milling, who is the manufacturer of the milling machine?

Have look at this webside, this rectifier diodes look much alike.
https://www.ebay.com/itm/Diode-Rectifier-75-Amp-1200-Volt-Vintage-Restoration-Part-Tested-Qty-of-2-/321099522209
Manfred
Resistor Ronker
 
Posts: 446
Joined: 05 Apr 2009, 00:42
Has thanked: 760 times
Have thanks: 338 times

Re: BJFE-Baby Blue

Postby momo lab » 14 Nov 2017, 14:48

Manfred wrote:I have done some calculations and found that the value R5 ist to high.
Please check it again, maybe is the value 14.7 Kohms not 47 kohms.

Cool milling, who is the manufacturer of the milling machine?

Have look at this webside, this rectifier diodes look much alike.
https://www.ebay.com/itm/Diode-Rectifier-75-Amp-1200-Volt-Vintage-Restoration-Part-Tested-Qty-of-2-/321099522209



Today I have reworked the PCB and tested it, except for the low gain, which worked fine.
20.jpg

Schematic diagram before the ground fault. Has been updated in V2.
23.JPG


19.JPG



This milling machine was made by myself three years ago, using only electric drills and saws. The production of a BB OD PCB about half an hour, but it is loud noise.
21.jpg


I found in another old Emerald Green thread that it uses the same diode and does not think this red diode is the same as it.

24.jpg

To make it easier to test for more diodes, I used a 24-segment switch to test more differently more quickly.

26.jpg

22.jpg

Communicate with everyone I use Google Translate, which was unthinkable 10 years ago, thank you all.
25.jpg
You do not have the required permissions to view the files attached to this post.

For this message the author momo lab has received thanks:
Manfred (14 Nov 2017, 20:30)
User avatar
momo lab
Degoop Doctor
 
Posts: 8
Joined: 25 Oct 2017, 12:49
Has thanked: 2 times
Have thanks: 23 times

Re: BJFE-Baby Blue

Postby marshmellow » 14 Nov 2017, 15:26

If you include a ground layer on your pcb, you would have to mill much less.

Print on the transistors is not readable?
marshmellow
Resistor Ronker
 
Posts: 395
Joined: 16 Aug 2007, 08:31
Location: Germany
Has thanked: 11 times
Have thanks: 87 times


Return to Boutique Stompboxes dissected...

Who is online

Users browsing this forum: edo.wicaksono, julessouren, ranko0537 and 13 guests