Verify it.gtrplaya101 wrote:Verified?
Emma - Reezafratzitz [ goop-alarm ] [traced]
Here you go, bigger pads! So still unverified, but it won't be long...
https://img17.imageshack.us/img17/9978/layoutw.png
https://img253.imageshack.us/img253/92/ ... ansfer.png
https://img17.imageshack.us/img17/9978/layoutw.png
https://img253.imageshack.us/img253/92/ ... ansfer.png
- marshmellow
- Cap Cooler
If you make sure that the schematic you have drawn is correct (by comparing with the original and using the ERC), Eagle does that for you if you use the DRC. That's what it's for.
Checked by DRC, made a few little changes.
Still not verified ofcourse.
https://img214.imageshack.us/img214/92/ ... ansfer.png
https://img83.imageshack.us/img83/9273/layouta.png
Still not verified ofcourse.
https://img214.imageshack.us/img214/92/ ... ansfer.png
https://img83.imageshack.us/img83/9273/layouta.png
It's still unverified, but here's the latest version of my PCB-design. The only jumper left is on a pot (bias). I corrected some extreme angles in the traces and gave some of the traces a bit more space.
https://img26.imageshack.us/img26/9978/layoutw.png
https://img8.imageshack.us/img8/92/readyfortransfer.png
https://img26.imageshack.us/img26/9978/layoutw.png
https://img8.imageshack.us/img8/92/readyfortransfer.png
Ok, at this point I've got a low gain output with a volume drop. All the pots work like they should, the LED is working correctly, the bypass signal is ok. I swapped a few components for other values (like 10nF instead of 6n8, 91pF instead of 100pF) because I didn't have them, but I don't think that could be the problem. Could it be the IC? I used a 4069.
Any tips?
Any tips?
- quaternotetriplet
- Resistor Ronker
Please post the parts list. thanks
great job guys
I wish we make the board smaller that it would fit to a small 1290NS enclosure!!!
Btw, tnx alot!!!! weeeeeeeeeeee
I wish we make the board smaller that it would fit to a small 1290NS enclosure!!!
Btw, tnx alot!!!! weeeeeeeeeeee
I can post eagle files on request, I've got some sound samples here! It's clean, clone, original.
http://www.gitaar.net/forum/index.php/f ... eeza_1.mp3
http://www.gitaar.net/forum/index.php/f ... eeza_2.mp3
http://www.gitaar.net/forum/index.php/f ... eeza_3.mp3
No volume problems at all, works like a charm. Here's my build, next to an original:
*edit* just so you know, all of the samples were recorded using a fender strat, into a hotrod deluxe.
http://www.gitaar.net/forum/index.php/f ... eeza_1.mp3
http://www.gitaar.net/forum/index.php/f ... eeza_2.mp3
http://www.gitaar.net/forum/index.php/f ... eeza_3.mp3
No volume problems at all, works like a charm. Here's my build, next to an original:
*edit* just so you know, all of the samples were recorded using a fender strat, into a hotrod deluxe.
- Barcode
- Diode Debunker
Well, is the layout you posted just before my post the same? Is that the functional one? If so, no need for the Eagle files as far as I'm concerned.miwanone wrote:I can post eagle files on request, I've got some sound samples here! It's clean, clone, original.
http://www.gitaar.net/forum/index.php/f ... eeza_1.mp3
http://www.gitaar.net/forum/index.php/f ... eeza_2.mp3
http://www.gitaar.net/forum/index.php/f ... eeza_3.mp3
No volume problems at all, works like a charm. Here's my build, next to an original:
*edit* just so you know, all of the samples were recorded using a fender strat, into a hotrod deluxe.
Greetings! I badly speak in English, therefore I am sorry.miwanone wrote:I can post eagle files on request, I've got some sound samples here! It's clean, clone, original.
http://www.gitaar.net/forum/index.php/f ... eeza_1.mp3
http://www.gitaar.net/forum/index.php/f ... eeza_2.mp3
http://www.gitaar.net/forum/index.php/f ... eeza_3.mp3
It seemed to me that sound examples under these references:
http://www.gitaar.net/forum/index.php/f... eeza_2.mp3
And
http://www.gitaar.net/forum/index.php/f... eeza_3.mp3
The identical. I am mistaken?