Keeley - 30ms Double Tracker

General documentation, gut shot, schematic links, ongoing circuit tracing, deep thoughts ... all about boutique stompboxes.
Post Reply
User avatar
floris
Cap Cooler
Information
Posts: 473
Joined: 14 Oct 2007, 12:05
Has thanked: 231 times
Been thanked: 72 times

Post by floris »

Keeley 30ms Double Tracker gutshots.

Spin Semiconductor FV-1 for audio delay / detune / reverb: http://www.spinsemi.com/products.html
24LC32A 8pin DIP EEPROM that holds the program for the FV-1 chip.
TL074 for the audio path, probably buffers and such to interface with the FV-1 chip.
TQ2-9V "single side stable" DPDT relay that is used for true bypass next to a 3PDT foot-switch.
4x 10kB pots for controlling the parameters of the program running on the FV-1 chip.
Keeley 30ms Double Tracker
Keeley 30ms Double Tracker
PCB bottom 1
PCB bottom 1
PCB bottom 2
PCB bottom 2
PCB top
PCB top
FV-1
FV-1
TL074
TL074
TQ2-9V relay & 24LC32A EEPROM
TQ2-9V relay & 24LC32A EEPROM

User avatar
caspercody
Resistor Ronker
Information
Posts: 388
Joined: 15 Jul 2009, 14:34
Has thanked: 34 times
Been thanked: 48 times

Post by caspercody »

Check out Pedalpcb.com Unison Double tracker. Might help with the schematic.

http://www.pedalpcb.com/product/unison/

User avatar
Boba7
Information
Posts: 44
Joined: 14 May 2015, 23:05
Has thanked: 25 times
Been thanked: 13 times

Post by Boba7 »

A relay AND a 3pdt?

User avatar
floris
Cap Cooler
Information
Posts: 473
Joined: 14 Oct 2007, 12:05
Has thanked: 231 times
Been thanked: 72 times

Post by floris »

Boba7 wrote:A relay AND a 3pdt?
Yes I also found that interesting. Seems overkill.

Also the PCB mentions a "trails" function next to the 2 DIP switches and at the bottom of the PCB.
But this is not implemented as far as I can see.

User avatar
Boba7
Information
Posts: 44
Joined: 14 May 2015, 23:05
Has thanked: 25 times
Been thanked: 13 times

Post by Boba7 »

floris wrote:
Boba7 wrote:A relay AND a 3pdt?
Yes I also found that interesting. Seems overkill.
Is the 3pdt latching or momentary?

User avatar
floris
Cap Cooler
Information
Posts: 473
Joined: 14 Oct 2007, 12:05
Has thanked: 231 times
Been thanked: 72 times

Post by floris »

Boba7 wrote:Is the 3pdt latching or momentary?
It is a latching switch.

User avatar
floris
Cap Cooler
Information
Posts: 473
Joined: 14 Oct 2007, 12:05
Has thanked: 231 times
Been thanked: 72 times

Post by floris »

Some picts with IC1 TL074 quad opamp removed:
TL074 removed 1
TL074 removed 1
TL074 removed 2
TL074 removed 2
Opamp B has minus input and output connected together so it is a buffer.
Opamp C has a resistor between input and output and works as an amplifier or mixer.
Opamp D is not used.

In my pedal, the signal was very soft.
Measurements on the IC1 TL074 pins showed that the opamps were not working properly: Output pins were not at V-bias of 4,5V DC.
I replaced IC1 with a new TL074, and all is working again. :thumbsup

Post Reply